According to customer requirements, it can be made of 45#, 40Cr, 30CrMo, 35CrMo, 42CrMo, 18CrNiMo7-6 and other materials. According to different weights, it can be forged on different forging equipment units. The weight of forged products can reach 6kg-5000kg, Forging needs to be completed through heating, pre-forging, forming and other processes.Stainless steel forgings refer to the articles in which stainless steel materials are pressed to shape the required shape or suitable compression force through plastic deformation.This force is typically achieved by using a hammer or pressure.
Contact Now
According to customer requirements, it can be made of 45#, 40Cr, 30CrMo, 35CrMo, 42CrMo, 18CrNiMo7-6 and other materials. According to different weights, it can be forged on different forging equipment units. The weight of forged products can reach 6kg-500kg, Forging needs to be completed through heating, pre-forging, forming, trimming and other processes.The design of forged steel and the abrasive tools for its production require initial costs.
Contact Now
According to customer requirements, it can be made of 45#, 40Cr, 30CrMo, 35CrMo, 42CrMo, 18CrNiMo7-6 and other materials. According to different weights, it can be forged on different forging equipment units. The weight of forged products can reach 6kg-500kg, Forging needs to be completed through heating, pre-forging, forming, trimming and other processes.Flange is also called flange plate or flange. Flanges are the parts that connect pipes to each other and are connected to pipe ends. There are holes on the flange, and the bolts make the two flanges tightly connected.
Contact Now
After heating and repeated forging, it can also be modulated heat treatment and finishing according to customer requirements, so after repeated forging, the forging ratio is high, the durability is good, and it is suitable for key accessories of equipment.
Contact Now
According to customer requirements, it can be made of 45#, 40Cr, 30CrMo, 35CrMo, 42CrMo, 18CrNiMo7-6 and other materials. According to different weights, it can be forged on different forging equipment units. The weight of forged products can reach 6kg-500kg. Heating, pre-forging, forming, trimming and other processes are completed.Coupling refers to a device that connects two shafts or shafts and rotating parts, rotates together during the transmission of motion and power, and does not disengage under normal conditions.
Contact Now
The driving shaft forgings produced by our company are mainly used in construction machinery industry, petroleum industry and wind power industry. The raw materials are hot rolled round steel or ingot recognized at home and abroad. According to customer's requirements, we can carry out hot forging and forming, and meet the requirements of ultrasonic testing (UT). Forging can improve product performance and save cost.
Contact Now
Shaft: one of the main parts in machinery. Generally, it is a metal round rod around which wheels and other rotating parts rotate or follow it.As a big category, shafts are subdivided into intermediate shafts, crankshafts, driving shafts, etc.The intermediate shaft forgings produced by our company are mainly used in construction machinery industry, petroleum industry and wind power industry. The raw materials are hot rolled round steel or ingot recognized at home and abroad.
Contact Now
Our company has many years of experience in petroleum product processing, and has API certificate and SQ1 certificate. For casing heads, our company can forge 10kg-5000kg forgings, and can forge a variety of materials including 42CrMo, 4140, 4130, 40Cr, 20CrMnMo, 18CrNiMo7-6, 410SS. The product is formed by heating and repeated forging, so that the forging ratio after forging is high, the durability is good, and it is suitable for key accessories of equipment.The casing head is generally made of 35 or 42 chrome molybdenum high-quality alloy structural steel.
Contact Now
Flange, also known as flange or flange. Flange is a part of connecting shaft, which is used to connect pipe ends; It is also used for flanges on the inlet and outlet of equipment, and is used for the connection between two equipment, such as reducing pipe flanges. There are holes in the flanges, and bolts make the two flanges closely connected. All connecting parts that are bolted around two planes and closed at the same time are generally called "flanges", such as the connection of ventilation pipes. Such parts can be called "flange parts".
Contact Now
Connectors refer to components used to connect electrical components or electronic devices, which are an indispensable part of electronic circuits.Our Baohua Company was founded in 1969. After three generations' hard work, it now covers an area of 50,000 ㎡ and has a building area of 25,000 ㎡. There are 260 employees and 46 engineering technicians. The annual output of forgings is 30,000 tons.
Contact Now
The materials we use in the production of torque arm are generally made of 45 or 40Cr steel. According to the drawings provided by customers, through a series of processes such as forging, tempering, lathe machining, hobbing, drilling, quenching, flaw detection, high-temperature tempering, testing and packaging, the torque arm products that meet the needs of customers are created.
Contact Now
Hangers produced by our company are mainly used in petroleum industry. Raw materials are purchased from round steel with recognized quality at home and abroad. We can forge the corresponding model of dies and hammers according to customers' requirements, thus improving production efficiency and saving time.
Contact Now
The joint seats produced by our company are mainly used in wind power generation industry. Raw materials are purchased from hot rolled round steel or steel ingots recognized at home and abroad. We can carry out hot forging according to customers' requirements, and meet the requirements of ultrasonic flaw detection (UT). Forging can improve product performance and save costs.
Contact Now
A device used to plug a specific well layer or reservoir in a casing, which can prevent the flow of fluid by expansion or differential pressure sealing.Material45#Hardness241-287Inner Diameter50.8Outside Diameter223.5Our Baohua Company was founded in 1969. After three generations' hard work, it now covers an area of 50,000 ㎡ and has a building area of 25,000 ㎡. There are 260 employees and 46 engineering technicians. The annual output of forgings is 30,000 tons.
Contact Now
Our BaoHua business enterprise is a nation-owned agency, which has a history of more than 60 years. from the preliminary forging of iron parts to the existing roughing, warmth treatment and finishing of forgings. devices and device additionally observe the contemporary product manufacturing requirements. at present, there are more than 80 units of processing equipment, together with zeiss 3-coordinate, eastern small plate contour meter, equipment tester, omega device counter and other inspection and trying out device. the company has handed iso9001, api, sq.
Contact Now
Our Baohua Company is a state-owned to private enterprise. The family business has a history of more than 60 years, from the initial forging iron pieces to the current rough processing, heat treatment and finishing of forgings. Instruments and equipment also closely follow the requirements of modern product production. At present, there are more than 80 processing equipment, as well as ZEISS CMM, Japanese small board profiler, gear detector, Ω MEGA tool setting instrument and other inspection and detection equipment.
Contact Now
Our company employs a new seamless rolled ring process to provide forged gear manufacturers with shape, size and material flexibility, lower volume requirements and near-finish shapes to save on final tooling costs. All of our forgings can go through hot die forging, rough machining, heat treatment and other processes, and the forgings can be finished to reach the final assembly condition.
Contact Now
Our Baohua Company is a state-owned enterprise, which has a history of more than 60 years. From the initial forging of iron parts to the present roughing, heat treatment and finishing of forgings. Instruments and equipment also follow the current product production requirements. At present, there are more than 80 sets of processing equipment, including ZEISS three-coordinate, Japanese small plate contour meter, gear tester, Omega tool counter and other inspection and testing equipment.
Contact Now
This product may be time and again solid after heating, and also can be modulated and heat handled and finished according to purchaser necessities. after repeated forging, the forging ratio is excessive and the durability is good. it's miles suitable for key elements of gadget. for casing heads, our employer can forge 10kg-5000kg forgings, and can forge an expansion of materials along with 42CrMo, 4140, 4130, 40Cr, 20CrMnMo, 18CrNiMo7-6, 410ss.
Contact Now
Flange has the blessings of high electricity, excellent sealing, handy upkeep, robust adaptability and reusability, which makes it an essential and essential factor in pipeline system. the subsequent is the product records. MATERIAL4130-75KHARDNESS207-237INNER DIAMETER57.76OUTSIDE DIAMETER304.65Our baohua business enterprise turned into based in 1969. after three generations' tough paintings, it now covers an area of fifty,000 ㎡ and has a building vicinity of 25,000 ㎡. there are 260 employees and forty six engineering technicians. the once a year output of forgings is 30,000 lots.
Contact Now
This product can be repeatedly forged after heating, and can also be modulated and heat treated and finished according to customer requirements. After repeated forging, the forging ratio is high and the durability is good. It is suitable for key parts of equipment. For casing heads, our company can forge 10kg-5000kg forgings, and can forge a variety of materials including 42CrMo, 4140, 4130, 40Cr, 20CrMnMo, 18CrNiMo7-6, 410SS.
Contact Now
The high neck flange produced by using our baohua company is specially used inside the accessories of gadget in the petroleum industry. forging the dimensions of excessive neck flange consistent with the necessities of clients for the usage of spherical steel in product materials.
Contact Now
The flanges produced by our Baohua company are mainly used in the oil industry and equipment accessories of construction machinery. Forging flange size according to customer's requirements of using round steel in product materials.
Contact Now
Our baohua employer became founded in 1969. after three generations' hard paintings, it now covers an area of 50,000 ㎡ and has a constructing location of 25,000 ㎡. there are 260 personnel and 46 engineering technicians. the once a year output of forgings is 30,000 heaps. mainly in the car, hydraulic equipment, wind strength era, petroleum machinery parts, creation equipment, mining, metallurgy, shipbuilding machinery and other industries to supply related accessories. the goods bought are oriented at domestic and abroad.
Contact Now
